192.168.80.240 – Router Login Admin Page

What Is 192.168.80.240?

192.168.80.240 is a private IP address that serves as a default gateway for specific Amped Wireless router models. Type it into a browser while connected to your Amped Wireless network and it opens the router’s admin dashboard — the panel where you manage your Wi-Fi name and password, connected devices, security settings, parental controls, port forwarding, and firmware updates.

The 192.168.80.x subnet is highly unusual for a home router. Most routers use 192.168.0.x, 192.168.1.x, or similar low-numbered subnets. Amped Wireless chose 192.168.80.240 for a specific subset of their product lineup — primarily their high-end and enterprise-grade models. This unusual address helps prevent conflicts when these devices are used as range extenders or secondary routers behind an existing network already using the more common 192.168.x.1 ranges.

Like all private IP addresses, 192.168.80.240 is completely invisible to the public internet. It belongs to the private address space reserved under RFC 1918 private address ranges — addresses that exist only on local networks and can’t be reached from mobile data, other Wi-Fi networks, or anywhere outside your own home. That isolation is by design.

Amped Wireless also supports a domain-based login URL: http://setup.ampedwireless.com. On any Amped Wireless router, this domain points to the same admin panel as typing the IP directly. If 192.168.80.240 isn’t loading for you, trying setup.ampedwireless.com in your address bar is a quick alternative check.

Which Amped Wireless Models Use 192.168.80.240?

Amped Wireless models are split between two default gateway addresses:

If you have one of the models listed above and 192.168.80.240 isn’t loading, try 192.168.3.1 as the fallback — some models support both addresses depending on firmware version and connection mode.

Default Credentials for 192.168.80.240

Good news: Amped Wireless keeps this simple.

That’s it. Every Amped Wireless router defaults to admin / admin. If those credentials don’t work, either the password was changed after setup or you need to check whether you’ve connected to the right network.

Other brands at this address (rare): If your router is not an Amped Wireless device and 192.168.80.240 is showing as your Default Gateway, your network was manually configured to use the 192.168.80.x subnet. In that case, try these common fallbacks:

How to Log Into 192.168.80.240 on a PC

The most common failure before credentials are even tried: typing the IP into the search bar instead of the address bar. The search bar sends your input to Google. The address bar navigates your browser directly to the page. They both sit at the top of your browser window but do completely different things.

1. Connect your PC to your Amped Wireless router — via Ethernet cable or Wi-Fi. Ethernet is recommended if you’re changing wireless settings, since your Wi-Fi connection could drop mid-save.
2. Open any browser — Chrome, Firefox, Edge, or Safari.
3. Click the address bar at the very top of the browser — the strip where URLs normally appear (like https://google.com).

4. Type 192.168.80.240 and press Enter. Alternatively, try http://setup.ampedwireless.com — both go to the same admin panel.
5. Enter admin for both username and password.
6. Click Login.

If you’re in — jump to “What to Do After You Log In.” If not, the troubleshooting section below covers the five most likely causes.

How to Log Into 192.168.80.240 on a Phone

No other guide for this specific IP address provides any mobile login guidance. Here are separate, platform-specific steps for iPhone and Android.

On iPhone (Safari)

1. Connect your iPhone to the Amped Wireless network. Make sure you’re on this router’s specific network — not a guest SSID, not a nearby hotspot.
2. Open Safari. Tap the URL address bar at the top of the app — not the search bar on Safari’s home screen, not Spotlight.
3. Type 192.168.80.240 and tap Go. Or try setup.ampedwireless.com as an alternative.
4. The Amped Wireless login page should load. Enter admin / admin and tap Login.

On Android

1. Connect your Android phone to your Amped Wireless Wi-Fi. Watch for Android’s background mobile data behavior — Android sometimes keeps mobile data active even when Wi-Fi shows connected, routing traffic through mobile data instead of your local network. Local addresses like 192.168.80.240 only respond through your local network, not through mobile data.
2. Open Chrome or your preferred browser.
3. Tap the address bar at the top.
4. Type 192.168.80.240 and tap Go. The setup.ampedwireless.com URL is a reliable alternative here too.
5. Enter admin / admin and tap Login.

Troubleshooting — 5 Reasons 192.168.80.240 Won’t Load

Factory Reset Guide for 192.168.80.240 Routers

If the admin password was changed and you can’t recover it, a factory reset returns the router to factory defaults — including restoring admin/admin credentials and the original gateway address.

Amped Wireless uses two reset methods depending on the model:

Method 1 — Standard Reset (Most Models)

Back up your config first if you can still log in. Go to Administration or System Tools and look for a Backup or Save Configuration option. Export that file — it saves significant reconfiguration time after the reset.

What gets wiped:

• Admin username and password (reverted to admin / admin)
• Wi-Fi name (SSID) and password
• Port forwarding rules
• Parental controls and URL filters
• Static IP / DHCP reservations
• Custom DNS settings

Steps:

1. Keep the router powered on.
2. Find the Reset button — a small recessed pinhole on the back or bottom.
3. Use a straightened paperclip or SIM ejector.
4. Press and hold for 10 seconds until the LEDs blink or change.
5. Release and wait 60–90 seconds for a full reboot.
6. Try 192.168.80.240 with admin / admin.

Method 2 — Amped Wireless 30-30-30 Reset (If Standard Reset Fails)

Amped Wireless specifically recommends the 30-30-30 reset procedure for their routers when a standard reset doesn’t fully restore factory settings. This is unique to Amped Wireless hardware and significantly more thorough than a standard 10-second reset.

Steps:

1. With the router powered on, press and hold the Reset button for 30 seconds.
2. While still holding the Reset button, unplug the power cable. Keep holding for another 30 seconds with power disconnected.
3. While still holding the Reset button, plug the power cable back in. Hold for a final 30 seconds.
4. Release the Reset button. Total hold time: 90 seconds.
5. Wait 90–120 seconds for the router to fully reboot.
6. Try 192.168.80.240 with admin / admin.

This 30-30-30 procedure clears all NVRAM (non-volatile memory), which ensures a more complete wipe than a standard reset. If your standard reset left some settings in place, this will finish the job.

Reset hold times for other brands at this address:

What to Do After You Log In

Once you’re inside the Amped Wireless admin panel, here’s what to actually configure — in order of importance.

Change Your Admin Password

admin / admin is the first credential any attacker on your network will try. Change the admin password immediately after first login.

1. Log into 192.168.80.240 (or setup.ampedwireless.com).
2. Navigate to Administration, Management, or Advanced in the menu. On Amped Wireless routers, look for System Settings → Admin Password or Management → Change Password.
3. Enter your current password (admin), then your new one twice.
4. Choose something long and memorable — a passphrase of three or four random words beats a short complex string for both security and memorability. Following NIST password guidelines is worthwhile here: length matters more than special characters.
5. Save and log back in with the new credentials.

Change Your Wi-Fi Name and Password

Go to Wireless Settings or Wi-Fi Settings. Change the SSID — Amped Wireless routers often ship with SSIDs like Amped_Network, Amped_B1900RT_2.4, or Amped_ALLY_XXXX. These SSIDs instantly identify your router brand and model to anyone scanning nearby. Change it to something neutral. Set a strong Passphrase. After saving, all devices will need to reconnect.

Check Dual-Band Settings

High-end Amped Wireless models like the R10000, B1900RT, and RTA2600 are dual-band or tri-band routers with separate 2.4 GHz and 5 GHz radios. Each band can have its own SSID and password, or you can use the same name for both — called a unified SSID or band steering. Most modern devices handle this automatically, but manually splitting the bands can be useful if you have older 2.4 GHz-only devices that struggle to connect on a unified SSID.

Set Your Encryption to WPA2 or WPA3

In wireless settings, find the Security Mode or Encryption Type field. If it shows WEP — change it right now. WEP can be broken in seconds. The minimum standard today is WPA2-Personal. Many Amped Wireless high-end models support WPA2 vs WPA3 — if yours does, WPA3 offers meaningfully stronger protection against brute-force attacks. Use it.

Check Connected Devices

Under DHCP Client List, Connected Devices, or Network Map, you’ll see every device currently on your network. Each entry shows a device name, assigned IP, and what is a MAC address — a unique hardware identifier. Look for anything unfamiliar. Amped Wireless high-end routers can handle a large number of connected devices; scanning this list periodically is worth the few seconds it takes.

Set Up a Guest Network

Amped Wireless routers support guest networks — a separate, isolated Wi-Fi zone that gives visitors internet access without exposing your main network. They can browse the web but can’t see your computers, printers, smart home devices, or NAS drives. Look for Guest Network in the wireless settings. See how to set up a guest network for a detailed walkthrough.

Port Forwarding

If you run anything that needs to be reachable from outside your network — a game server, home NAS, security camera system, remote desktop — configure it under Port Forwarding or NAT in your router menu. Understanding how port forwarding works before making changes is the best way to avoid the most common setup mistakes.

Update Firmware

Go to Administration → Firmware Update or check System → Software Upgrade. Amped Wireless has historically released firmware updates that improve performance and fix vulnerabilities on their high-end models. Check for updates and install any available. Given that some Amped Wireless models were sold as premium products with long product lifecycles, staying current on firmware is especially important.

Which Brands Use 192.168.80.240?

Primary Brand: Amped Wireless

Amped Wireless is the only major brand that uses 192.168.80.240 as a factory-default gateway. Amped Wireless is a US-based networking company that made a name for itself with high-power, long-range routers and range extenders targeting homes with dead zones and large spaces.

Confirmed Amped Wireless models at this address:

• R10000 — high-power AC3000 tri-band router
• B1900RT — AC1900 dual-band router
• RTA2600 (Athena) — AC2600 MU-MIMO router
• RE2200T (Helios) — range extender with router mode
• ALLY-00X21K — mesh Wi-Fi system

These models also respond to 192.168.3.1 (Amped Wireless’s primary default) and setup.ampedwireless.com in most firmware versions — meaning you typically have three ways to reach the admin panel.

Note: Amped Wireless ceased active sales operations and product development around 2020–2021, though their routers remain in widespread use. Firmware updates are no longer being issued for most models. If you have an older Amped Wireless device, check the router-network.com model page to see the last available firmware version.

Frequently Asked Questions